Utilisateur
- S'identifier
- S'enregistrer

ADHESIVE CEMENT EXTRA C2

Precautions and Recommendations

Do not use below 5ºC or above 30ºC.

Do not use if there is a risk of frost, rain, strong winds, or direct sunlight.

In extreme weather conditions (strong winds or high temperatures), drying may occur more quickly than usual.

It is recommended to leave a peripheral expansion joint of approximately 5 mm between the floor and the wall or pillar, hidden by the baseboard.

Presentation

25 kg laminated paper bags.

Storage for up to 1 year in the original packaging, protected from weather and humidity.

Technical Data

(Statistical results obtained under standard conditions)

Appearance: WHITE or GREY powder

Adjustment time: Approximately 30 minutes (depending on climatic conditions)

Useable Life (UBL): Approximately 2 hours (depending on climatic conditions)

Initial adhesion: ≥ 1 N/mm²

Adhesion after exposure to water: ≥ 1 N/mm²

Adhesion after aging under the action of heat: ≥ 1 N/mm²

Adhesion after freeze-thaw cycle: ≥ 1 N/mm²

Service temperature: -30ºC to 90ºC

Classification according to NF EN 12004 :2008 C2

Note

The instructions in this manual are based on our tests and knowledge, and do not imply any commitment on the part of SARL RITAL or release the consumer from the responsibility of checking and verifying the products for their correct use. Claims must be accompanied by the original packaging to allow for proper traceability.

SARL RITAL assumes no responsibility, under any circumstances, for the application of its products or construction solutions by the application company or other parties involved in the application and/or execution of the project in question. RITAL's liability is limited exclusively to possible damages directly or exclusively attributable to the products supplied, individually or integrated into systems, due to manufacturing defects.

Description
Vidéos
Fiches techniques
Plus d'informations

Precautions and Recommendations
Do not use below 5ºC or above 30ºC.
Do not use if there is a risk of frost, rain, strong winds, or direct sunlight.
In extreme weather conditions (strong winds or high temperatures), drying may occur more quickly than usual.
It is recommended to leave a peripheral expansion joint of approximately 5 mm between the floor and the wall or pillar, hidden by the baseboard.
Presentation
25 kg laminated paper bags.
Storage for up to 1 year in the original packaging, protected from weather and humidity.

Technical Data
(Statistical results obtained under standard conditions)

Appearance:                                                WHITE or GREY powder
Adjustment time:                 Approximately 30 minutes (depending on climatic conditions)
Useable Life (UBL):                 Approximately 2 hours (depending on climatic conditions)
Initial adhesion:                                                                      ≥ 1 N/mm²
Adhesion after exposure to water:                                     ≥ 1 N/mm²
Adhesion after aging under the action of heat:                  ≥ 1 N/mm²
Adhesion after freeze-thaw cycle:                                        ≥ 1 N/mm²
Service temperature:                                                        -30ºC to 90ºC
Classification according to NF EN 12004 :2008                                   C2
Note
The instructions in this manual are based on our tests and knowledge, and do not imply any commitment on the part of SARL RITAL or release the consumer from the responsibility of checking and verifying the products for their correct use. Claims must be accompanied by the original packaging to allow for proper traceability.
SARL RITAL assumes no responsibility, under any circumstances, for the application of its products or construction solutions by the application company or other parties involved in the application and/or execution of the project in question. RITAL's liability is limited exclusively to possible damages directly or exclusively attributable to the products supplied, individually or integrated into systems, due to manufacturing defects.
C2
- Comment utiliser:
  Instructions
  Add water and mix manually or mechanically until a smooth, workable consistency is obtained.
  Let the paste rest for approximately 5 minutes and knead it again.
  Spread the mixed product onto the substrate using a trowel to a maximum area of 2 m².
  Combine with a notched trowel to adjust the thickness (see table).
  Place the pieces on the fresh adhesive, pressing and moving until the grooves are completely flattened and the entire surface of the ceramic tile is properly bonded. Periodically check the adhesion of the adhesive by lifting a previously laid tile; if you observe a film without transfer on the surface of the adhesive or if the adhesive dehydrates, remove the material and apply a new product.
  Respect construction joints (expansion, contraction, expansion, and peripheral corner joints) and joints between tiles (minimum 2 mm on the inside and 5 mm on the outside).
  Joints must be filled after 24 hours for vertical surfaces and 48 hours for floors. Use the appropriate mortar from the RITAL JOINT COMPUND RANGE, depending on the type of joint.

ADHESIVE CEMENT EXTRA C2

Notre selection

ADHESIVE CEMENT C1

ADHESIVE CEMENT C1 GREY

ADHESIVE CEMENT C1E

ADHESIVE CEMENT EXTRA C2

COARSE FILLER COATING 611

WATERPROOF COATING 510

ADHESIVE CEMENT Flex C2 TE S1

SINGLE-LAYER MORTARS

JOINT COMPOUND 1-3-5 KG

Catalogue

Contactez nous

À propos