ADHESIVE CEMENT Flex C2 TE S1

Precautions and Recommendations

Do not use below 5ºC or above 30ºC.

Do not use if there is a risk of frost, rain, strong winds, or direct sunlight.

In extreme weather conditions (strong winds or high temperatures), drying may occur more quickly than usual.

It is recommended to leave a peripheral expansion joint of approximately 5 mm between the floor and the wall or pillar, hidden by the baseboard.

Presentation

25 kg laminated paper bags.

Storage for up to 1 year in the original packaging, protected from weather and humidity.

 

Appearance:                                                                                            WHITE

Mixing water for white product:                                                           29.5 ± 2%

Mixing water for gray product:                                                                30 ± 2%

Apparent dust density:                                                                1.5 ± 0.2 g/cm3

Mixed product density:                                                                1.7 ± 0.2 g/cm3

Adjustment time:              Approximately 30 min. (Depending on climatic conditions)

Paste pot life:                      Approximately 2 h. (Depending on climatic conditions)

Initial adhesion                                                                                              > 1.0 N/mm²

Adhesion after water exposure                                                                > 1.0 N/mm²

Adhesion after aging under heat                                                              > 1.0 N/mm²

Adhesion after freeze-thaw cycle                                                             > 1.0 N/mm²

Classification according to NF EN 12004:2008                                                      C2 TE

Classification according to NF EN 12002:2009                                                              S1

 

Note

The instructions in this manual are based on our tests and knowledge, and do not imply any commitment on the part of SARL RITAL or release the consumer from the responsibility of checking and verifying the products for their correct use. Claims must be accompanied by the original packaging to allow for proper traceability.

SARL RITAL assumes no responsibility, under any circumstances, for the application of its products or construction solutions by the application company or other parties involved in the application and/or execution of the project in question. RITAL's liability is limited exclusively to possible damages directly or exclusively attributable to the products supplied, individually or integrated into systems, due to manufacturing defects.

 

  • Precautions and Recommendations

    Do not use below 5ºC or above 30ºC.

    Do not use if there is a risk of frost, rain, strong winds, or direct sunlight.

    In extreme weather conditions (strong winds or high temperatures), drying may occur more quickly than usual.

    It is recommended to leave a peripheral expansion joint of approximately 5 mm between the floor and the wall or pillar, hidden by the baseboard.

    Presentation

    25 kg laminated paper bags.

    Storage for up to 1 year in the original packaging, protected from weather and humidity.

     

    Appearance:                                                                                            WHITE

    Mixing water for white product:                                                           29.5 ± 2%

    Mixing water for gray product:                                                                30 ± 2%

    Apparent dust density:                                                                1.5 ± 0.2 g/cm3

    Mixed product density:                                                                1.7 ± 0.2 g/cm3

    Adjustment time:              Approximately 30 min. (Depending on climatic conditions)

    Paste pot life:                      Approximately 2 h. (Depending on climatic conditions)

    Initial adhesion                                                                                              > 1.0 N/mm²

    Adhesion after water exposure                                                                > 1.0 N/mm²

    Adhesion after aging under heat                                                              > 1.0 N/mm²

    Adhesion after freeze-thaw cycle                                                             > 1.0 N/mm²

    Classification according to NF EN 12004:2008                                                      C2 TE

    Classification according to NF EN 12002:2009                                                              S1

     

    Note

    The instructions in this manual are based on our tests and knowledge, and do not imply any commitment on the part of SARL RITAL or release the consumer from the responsibility of checking and verifying the products for their correct use. Claims must be accompanied by the original packaging to allow for proper traceability.

    SARL RITAL assumes no responsibility, under any circumstances, for the application of its products or construction solutions by the application company or other parties involved in the application and/or execution of the project in question. RITAL's liability is limited exclusively to possible damages directly or exclusively attributable to the products supplied, individually or integrated into systems, due to manufacturing defects.

     

    • Comment utiliser:

      Features and Applications

      Indoor and outdoor use. Facades and swimming pools.

      Adhesion of all types of ceramic pieces. Recommended for large pieces.

      Eliminates the need to moisten substrates thanks to its water-retaining properties.

      No detachment. Excellent initial adhesion.

      Extended open time, allows for piece correction.

      Deformable

      Gluing of large surfaces with heavy traffic and radiantly heated floors.

      Substrates

      Conventional cement substrates.

      Substrates must be strong, stable, clean, and free of dust, formwork residue, organic products, etc.

      Interior and exterior ceramic floor and wall coverings.

      All substrates must be adequately flat. Otherwise, create raised surfaces of up to 5 mm with the same product 48 hours before bonding. For greater thicknesses, use traditional dry mortars or Self-Leveling Compound P900

      from the RITAL RANGE.

       

      In hot and windy conditions, or for highly absorbent substrates, moisten the substrate and wait until the water film disappears.

      Do not apply to plaster or paint.

      Instructions

      Add water and mix manually or mechanically until a smooth, workable consistency is obtained.

      Let the mixture rest for 5 minutes and mix again.